Preselector-Assembly

From HiQSDR
Jump to: navigation, search

Contents

HiQSDR Preselector Assembly

Preselector PCB Components

Preselector top parts overview as PDF

Preselector top parts overview

Preselector bottom parts overview as PDF

Preselector bottom parts overview


HiQSDR Filter assembly

Filter Module PCB Components

Filter module top parts overview

Filter module top parts overview

Filter module bottom parts overview

Filter module bottom parts overview


Filter assembly

All filters are relative simple to adjust, most of them do not need to be adjusted.
But:best Performance is always coupled with a good and clean work!

Use only good RF capacitors with <= 5% tolerance and wind the toroids cleanly as instructed!

You can use your HiQSDR as Vector Network Analyser (thanks to Jim, N2ADR!) to see and adjust your filter passbands!
If you use the HiQSDR as Analyser use an Attentuator to save the HiQSDR input. (-30dB Attentuator)
We used our HP Networkanalyser HP8752A to verify the filter designs and adjust our prototype filter modules.

This task is relative easy if you wind the cores exactly to the turns given and measure/correct the inductance with an good LCR-Meter.
We used for this task a new calibrated AGILENT U-1733C LCR-Meter with 0.25% tolerance, but any other good LCR meter (like the AAA-LCR Meter...) will do.

To test our filter modules we built a small test fixture to connect the modules to our network analyser.

Filter test fixture


Toroid core winding

The winding of the toroid cores are realy easy see our example of a tapped Toroid Amidon T30-6.
Wind as first the "cold" (lower) part of the turns up to the tap, spreading all turns over the toroid.
The circuit diagram shows as example "T30-6, 7+21=28T 0.3mm" that means:
Use Toroid Amidon T30-6, wind 28 turns with 0.3mm wire, tap at 7th turn.

First 7 turns.

First 7 turns


Make the tapping about some centimeters long and drill the two tapping wires.
Then wind the remainder of the needed turns onto the core evenly over the first windings.
Spread all remaining turns over the core so that you end again on the lower part of the toroid.

Second 21 turns.
Second 21 turns.


It may be helpful to use a little hint to mark the wire order:
Let the first wire about 2cm long, the tapping wires 3cm long and the last wire 4cm long.
With this different length of wires you can easily recognize the wire order!

Core ready to soldering.
Core ready to soldering


To correct the inductance, only remove or add turns of the the second winding!

You NEVER (!) will make the absolute correct inductance because a toroid can have only full turns, not half ones.

Try to be as narrow at the needed inductance as possible. (allow less than 5% tolerance!)
Sort the turns varfully with a small needle-nose-plier or tweezers to be evenly spread over the toroid.

Complete build 30m Filter module.
Complete build 30m Filter module



Position tapped cores

The begining of the tapped core must be at pcb ground. (Short end)

On the image we have marked the beginning of the tapped core with a red point.
Tapped core


HiQSDR Preselector connection

Image of the preselector connection to the HiQSDR board.
The preselector board contains some plugged filter boards and the 1 Watt amplifier from german magazine "Funkamateur".

Connected Preselector Board TOP Connected Preselector Board Bottom

Personal tools
Namespaces

Variants
Actions
HiQSDR
HiQSDR Board
RF Bridge
HiQSDR Preselector Board
HiQSDR 10 Enclosure
HiQSDR MPPA Amplifier
Under Development
HiQSDR Maker Site's
Exhibitions
Navigation
Toolbox
Translate